Untitled

Funder

Organizational Unit

Publications

A parameter for quantitative analysis of plasticity induced crack closure

Publication . Antunes, F.V.; Correia, Luís M.; Ramalho, Armando

Numerical models have been successfully developed to predict plasticity induced crack closure (PICC). However, despite the large research effort a full understanding of the links between physical parameters, residual plastic wake and PICC has not been achieved yet. The plastic extension of material behind crack tip, Dyp, obtained by the integration of vertical plastic deformation perpendicularly to crack flank, is proposed here to quantify the residual plastic field. The values of Dyp and PICC were obtained numerically in a M(T) specimen using the finite element method. An excellent correlation was found between PICC and Dyp which indicates that this parameter controls the phenomenon, and can be used to quantify the effect of physical parameters. An empirical model was developed to predict PICC assuming that the residual plastic field is a set of vertical plastic wedges, that the linear superposition principle applies and that the influence of a particular wedge exponentially decreases with distance to crack tip. The model was applied successfully to predict PICC for different residual plastic fields which provided an additional validation of Dyp as the parameter controlling PICC.

2015Journal article

Open access

A numerical study of the effect of single overloads on plasticity induced crack closure

Publication . Baptista, J.B.; Antunes, F.V.; Correia, Luís M.; Branco, R.

In this work, the effect of single overloads on plasticity induced crack closure is studied. An elastic-plastic finite element model was developed and the crack opening level was calculated from the contact forces along the crack flank. The effects of the loading parameters and stress state are analysed, and the mechanisms behind crack closure variations are identified. An overload is a traumatic event that eliminates material’s memory relative to the load history. Crack tip blunting is the mechanism behind this memory loss, since it eliminates crack closure. Material hardening has a major relevance on the evolution of plastic blunting, which was evident in the variation of the CTOD parameter. On the other hand, the overload produces strong plastic deformation ahead of the crack tip, giving rise to conditions for the rapid generation of crack closure higher than before the event. The peak of crack closure was found to increase linearly with the load increase above the maximum baseline value. The crack is totally closed for overload ratios of about 2.5. Empirical models were developed for the peak of crack closure, for the delay of this peak and for the stabilization distance after the overload. Finally, the stress state was found to have a major effect on crack closure level after an overload.

2017Journal article

Open access

Effect of compressive loads on plasticity induced crack closure

Publication . Antunes, F.V.; Correia, Luís M.; Camas, D.; Branco, R.

Compressive stresses play an important role on tension-compression fatigue which can be attributed to plasticity induced crack closure (PICC). The objective here is to study numerically the effect of compressive stresses on PICC and to discuss the applicability of PICC to explain the effect of negative stress ratios on fatigue crack growth rate. The compression produces reversed plastic deformation at the crack tip, reducing linearly the crack opening level. The incursion to negative stress ratios did not produce sudden changes in the behavior of PICC and no saturation with the decrease of minimum load was observed for δKeff. Crack closure was able to collapse da/dN-δK curves with negative stress ratios, indicating the applicability of the crack closure concept to explain the effect of negative R. The analysis of crack tip plastic strain range with and without contact of crack flanks confirmed the validity of crack closure concept.

2015Journal article

Open access

Effect of crack closure on non-linear crack tip parameters

Publication . Antunes, F.V.; Sousa, T.; Branco, R.; Correia, Luís M.

Crack closure concept has been widely used to explain different issues of fatigue crack propagation. However, some authors have questioned the relevance of crack closure and have proposed alternative concepts. The main objective here is to check the effectiveness of crack closure concept by linking the contact of crack flanks with non-linear crack tip parameters. Accordingly, 3D-FE numerical models with and without contact were developed for a wide range of loading scenarios and the crack tip parameters usually linked to fatigue crack growth, namely range of cyclic plastic strain, crack tip opening displacement, size of reversed plastic zone and total plastic dissipation per cycle were investigated. It was demonstrated that: (i) LEFM concepts are applicable to the problem under study; (ii) the crack closure phenomenon has a great influence on crack tip parameters decreasing their values; (iii) the ΔKeff concept is able to explain the variations of crack tip parameters produced by the contact of crack flanks; and (iv) the analysis of remote compliance is the best numerical parameter to quantify the crack opening level. Therefore the crack closure concept seems to be valid. Additionally, the curves of crack tip parameters against stress intensity factor range obtained without contact may be seen as master curves.

2015Journal article

Open access